Наверх

ОПМ 108010 Кольцо стопорное SH эксцентрическое осевое наружное дюймовое

Кольцо стопорное SH
Тип изделия: Стопорные кольца
Материал: Сталь

ОПМ 108010 Кольцо стопорное SH

ОПМ 108010 Кольцо стопорное SH эксцентрическое осевое наружное дюймовое.

RIMG NO. SHAFT DIAMETER GROOVE SIZE RING SIZE & WEIGHT CLEARANCE DIA. T THRUST LD.(lbS-) Sqr. Corner Abutment
DIAMETER WIDTH DEPTH FREE DIAMETER THICKNESS*** Weight Per 10G0 PCS. Ex- panded over Shaft Re- leased in Groove
Ring Safety Factor of 4 Groove Safety Factor of 2
Ds DEC Ds FRAC Ds mm
Dq Tol. W Tol. d Df Tol. T Tol. lbs. L1 L2 Pr Pa
**SH-12 .125 1/8 3.2 .117 ±.0015 .0015* .012 + .002 -.000 .004 .112 + .002 -.004 .010 ±001 .018 .222 .214 112 35
**SH-15 .156 5/32 4.0 .146 .012 .005 .142 .010 .037 .27 .260 132 55
**SH-18 .188 3/16 4.8 .175 .018 .006 .168 .015 ±.002 .059 .298 .286 244 80
**SH-19 .197 - 5.0 .185 .018 .006 .179 .015 .063 .319 .307 254 85
**SH-21 .219 7/32 5.6 .205 .018 .007 .196 .015 .074 .338 .324 284 110
**SH-23 .233 15/64 6.0 .222 .018 .007 .215 .015 .086 .355 .341 315 120
SH-25 .250 1/4 6.4 .230 .029 + .003 -.000 .010 .225 .025 .21 .45 .43 599 175
SH-27 .275 - 7.0 .255 ±.002 .002* .029 .010 .250 + .002 -.005 .025 .23 .48 .46 830 195
SH-28 .281 9/32 7.1 .261 .029 .010 .256 .025 .24 .49 .47 570 200
SH-31 .312 5/16 7.9 .290 .029 .011 .281 .025 .27 .54 .52 751 240
SH-34 .344 11/32 8.7 .321 .029 .011 .309 .025 .31 .57 .55 812 265
SH-35 .354 - 9.0 .330 .029 .012 .320 .025 .35 .59 .57 832 300
SH-37 .375 3/8 9.5 .352 .029 .012 .338 .025 .39 .61 .59 883 320
SH-39 .394 - 10.0 .369 .029 .012 .354 .025 .42 .02 .60 954 335
SH-40 .408 13/32 10.3 .382 .029 .012 .336 .025 .43 .53 .61 934 350
SH-43 .438 7/16 11.1 .412 .029 .013 .395 .025 .50 .66 .64 1035 400
SH-46SP1 .451 - 11.7 .435 .029 .013 .420 .025 .51 .68 .66 1110 460
SH-46 .459 15/32 11.9 .443 .029 .013 .428 .025 .54 .68 .66 1117 450
SH-50 .500 1/2 12.7 .468 ±.002 .004* .039 .016 .461 .035 .91 .77 .74 1675 550
SH-55 .551 - 14.0 .519 .039 .016 .509 + .005 -.010 .035 .90 .81 .78 1800 500
SH-56 .562 9/16 14.3 .530 .039 .016 .521 .035 1.1 .82 .79 1878 650
SH-59 .594 19/32 15.1 .559 ±.003 .004* .039 .017 .550 .035 1.2 .86 .83 1979 750
SH-62 .625 5/8 15.9 .588 .039 .018 .579 .035 1.3 .90 .87 2091 800
SH-66 .669 - 17.0 .629 .039 .020 .621 .035 1.4 .93 .89 2233 950
SH-66 .672 43/64 17.1 .631 .039 .020 .621 .035 1.4 .93 .89 2233 950
SH-G8 .688 11/16 17.5 .646 .046 .021 .635 .042 1.8 1.01 .97 3451 1000
SH-75 .750 3/4 19.0 .704 .046 .023 .693 .042 2.1 1.09 1.05 3756 1200
SH-78 .781 25/32 19.3 .733 .046 .024 .722 .042 2.2 1.12 1.08 3959 1300
SH-D1 .812 13/16 20.6 .762 .043 .025 .751 .042 2.5 1.15 1.10 4030 1450
SH-84 .844 - 21.4 .791 .046 .026 .780 .042 2.7 1.18 1.13 4200 1500
SH-87 .875 7/8 22.2 .821 .043 .027 .610 .042 2.8 1 21 1.16 4335 1550
SH-93 .938 15/16 23-8 .882 .043 .028 .837 .042 3.1 1.34 1.29 4720 1850
SH-9S .984 63/64 25.0 .926 .043 .029 .910 .042 3.5 1.39 1.34 4923 2000
SH-100 1 1 25.4 .940 .043 .030 .925 .042 3.6 1 41 1.35 5024 2100
SH-102 1.023 - 26.0 .961 .046 .031 .946 .042 3.9 1.43 1.37 5126 2250
SH-106 1.0S2 11/16 27.0 .998 ±.004 .005* .053 + .004 -.000 .032 .982 + .010 -.015 .050 4.8 1.50 1.44 6293 2400
SH-112 1.125 1-1/8 28.6 1.059 .056 .033 1.041 .050 5.1 1.55 1.49 6699 2600

RING NO. LUG HEIGHT MAXIMUM SECTION MINIMUM SECTION HOLE DIAMETER GAGING DIA. ALLOWABLE CORNER RADII & CHAMFERS MAX. LOAD w/ R max or Ch max (lbs.) EDGE MAR- GIN F.P.M. LIMITS Stan- dard Material
H Tol. S max Tol. S min Tol. R Tol. Gd Max R max Ch max P'r Y RPM
**SH-12 .046 ±.002 .018 ±.0015 .011 ±.0015 .026 +.010 -.002 .148 .010 .006 45 .012 80000
**SH-15 .054 .026 .016 .026 .189 .015 .009 45 .015 80000
**SH-18 .050 .025 ±.002 .016 ±.002 .025 .218 .014 .0085 105 .018 80000
**SH-19 .056 .026 .016 .026 .229 .0145 .009 105 .018 80000
**SH-21 .056 .028 .017 .026 .252 .015 .009 105 .021 80000
**SH-23 .056 .030 .019 .026 .272 .0165 .010 105 .021 80000
SH-25 .080 ±.003 .035 ±.003 .025 ±.003 .041 .290 .018 .011 470 .030 80000
SH-27 .081 .035 .024 .041 .315 .0175 .0105 470 .031 76000
SH-28 .080 .038 .025 .041 .326 .020 .012 470 .030 74000
SH-31 .087 .040 .026 .041 .357 .020 .012 470 .033 70000
SH-34 .087 .042 .0265 .041 .390 .021 .0125 470 .033 64000
SH-35 .087 .046 .029 .041 .405 .023 .014 470 .036 62000
SH-37 .083 .050 .0305 .041 .433 .026 .0155 470 .036 60000
SH-39 .087 .052 .031 .041 .452 .027 .016 470 .037 56500
SH-40 .087 .054 .033 .041 .408 .0285 .017 470 .036 55000
SH-43 .088 .055 .033 .041 .501 .029 .0175 470 .039 50000
SH-46SP1 .092 .064 .038 .041 .540 .015 .017 470 .039 42000
SH-46 .088 .060 .035 .041 .540 .031 .018 470 .039 42000
SH-50 .108 .065 ±.004 .040 ±.004 .047 .574 .034 .020 910 .048 40000
SH-55 .108 .053 .036 .047 .611 .027 .0165 910 .048 36000
SH-56 .108 .072 .041 .047 .644 .038 .023 910 .048 35000
SH-59 .109 .076 .043 .047 .680 .0395 .0235 910 .052 32000
SH-62 .110 .080 .045 .047 .715 .0415 .025 910 .055 30000
SH-66 .110 .082 .043 .047 .756 .040 .024 910 .060 29000
SH-66 .110 .082 .043 .047 .758 .040 .024 910 .060 29000
SH-68 .136 ±004 .084 ±.005 .048 ±-005 .052 .779 .042 .025 1340 .063 28000
SH-75 .136 .092 .051 .052 .850 .046 .0275 1340 .069 26500
SH-78 .136 .094 .052 .052 .883 .047 .028 1340 .072 25500
SH-31 .136 .096 .054 .052 .914 .047 .028 1340 .075 24500
SH-34 .137 .100 .057 .052 .950 .047 .028 1340 .078 24000
SH-37 .137 .104 .057 .052 .987 .051 .0305 1340 .081 23000
SH-93 .166 .110 .063 .078 +.015 -.002 1.054 .055 .033 1340 .084 21500
SH-98 .167 .114 .064 .078 1.106 .056 .0335 1340 .087 20500
SH-юо .167 .116 .065 .078 1.122 .057 .034 1340 .090 20000
SH-102 .168 .118 .066 .078 1.147 .058 .035 1340 .093 19500
SH-106 .181 .122 ±.006 .069 ±.006 .078 1.192 .060 .036 1950 .096 19000
SH-112 .182 .128 .071 .078 1.261 .063 .038 1950 .099 18800

RING NO. SHAFT DIAMETER GROOVE SIZE RING SIZE & WEIGHT CLEARANCE DIA. I THRUST LD.(lbs.)
DIAMETER WIDTH DEPTH FREE DIAMETER THICKNESS*** Weiqht Per 1000 DCS. Ex- panded over Shaft Re- leased In Groove Sqr. Corner Abutment
Rina Safety Factor of 4 Groove Safely Factor of 2
Ds DEC Ds FRAC Ds mm
Dq Tol. W Tol. d Df Tol. T Tol. lbs. L1 L2 Pr Pfl
SH-11B 1.188 1-3/16 30.2 1.118 ±.004 .005* .056 + .004 -.000 .035 1.098 + .010 -.015 .050 ±.002 5.6 1.61 1.54 7105 2950
SH-125 1.250 1-1/4 31.7 1.176 .056 .037 1.156 .050 5.9 1.69 1.62 7460 3250
SH-131 1.312 1-5/16 33.3 1.232 .056 .040 1.214 .050 6.8 1.75 1.67 7866 3700
SH-137 1.375 1-3/8 34.9 1.291 .056 .042 1.272 .050 7.2 1.80 1.72 8222 4100
SH-143 1.438 1-7/16 36.5 1.350 .056 .044 1.333 .050 8.1 1.87 1.79 8628 4500
SH-150 1.500 1-1/2 38.1 1.406 .056 .047 1.387 .050 9.0 1.99 1.90 8932 5000
SH-156 1.562 1-9/16 39.7 1.468 ±.005 .005* .068 .047 1.446 + .013 -.020 .062 + .003 12.4 2.10 2.01 11571 5200
SH-162 1.625 1-5/8 41.3 1.529 .068 .048 1.503 .062 13.2 2.17 2.08 12028 5500
SH-168 1.688 1-11/16 42.9 1.589 .068 .049 1.560 .062 14.8 2.24 2.15 12535 5850
SH-175 1.750 1-3/4 44.4 1.650 .068 .050 1.618 .062 15.3 2.31 2.21 12992 6200
SH-177 1.772 - 45.0 1.669 .068 .051 1.637 .062 15.4 2.33 2.23 13144 6400
SH-181 1.812 1-13/16 46.0 1.708 .068 .052 1.675 .062 15.6 2.38 2.28 13449 6650
SH-187 1.875 1-7/8 47.6 1.769 .068 .053 1.735 .062 17.3 2.44 2.34 13906 7000
SH-196 1.969 1-31/32 50.0 1.857 .068 .055 1.319 .062 18.0 2.57 2.46 14565 7800
SH-200 2.000 2 50.6 1.886 .068 .057 1.850 .062 19.0 2.60 2.49 14819 8050
SH-20G 2.062 2-1/16 52.4 1.946 ±.006 .006* .086 + .005 -.000 .058 1.905 + .015 -.025 .078 25.0 2.68 2.57 19234 8450
SH-212 2.125 2-1/8 54.0 2.003 .086 .061 1.964 .078 26.1 2.78 2.65 19793 9150
SH-215 2.156 2-5/32 54.6 2.032 .086 .062 1.993 .078 26.3 2.81 2.69 20097 9450
SH-225 2.250 2-1/4 57.1 2.120 .086 .065 2.081 .078 27.7 2.88 2.75 21011 10350
SH-231 2.312 2-5/16 58.7 2.178 .086 .067 2.139 .078 28.0 2.94 2.81 21518 10950
SH-237 2.375 2-3/8 60.3 2.239 .086 .068 2.197 .078 29.2 3.0S 2.93 22127 11400
SH-243 2.438 2-7/16 61.9 2.299 .086 .069 2.255 .078 29.5 3.07 2.94 22736 11900
SH-250 2.500 2-1/2 63.5 2.360 .086 .070 2.313 .078 29.7 3.17 3.03 23345 12350
SH-255 2.559 - 65.0 2.419 .086 .070 2.377 + .020 -.030 .078 33.9 3.18 3.04 23853 12650
SH-262 2.625 2-5/8 66.7 2.481 .086 .072 2.428 .078 35.0 3.30 3.16 24462 13350
SH-26B 2.688 2-11/16 68.3 2.541 .086 .073 2.485 .078 36.0 3.37 3.23 25071 13850
SH-275 2.750 2-3/4 69.8 2.602 .103 .074 2.543 .093 42.5 3.48 3.34 30551 14400
SH-287 2.875 2-7/8 73.0 2.721 .103 .077 2.659 .093 48.5 3.60 3.45 31973 15650
SH-293 2.938 2-15/16 74.6 2.779 .103 .079 2.717 .093 50.0 3.60 3.51 32683 16400
SH-30D 3.000 3 76.2 2.838 .103 .081 2.775 .093 52.0 3.60 3.44 33394 17200
SH-зов 3.062 3-1/16 77.8 2.898 .103 .082 2.832 .093 47.5 3.74 3.58 34003 17750
SH-312 3.125 3-1/8 79.4 2.957 .103 .084 2.892 .093 58.0 3.85 3.69 34815 18550
SH-315 3.156 3-5/32 80.2 2.986 .103 .085 2.920 .093 59.0 3.88 3.71 35119 18950
SH-325 3.250 3-1/4 82.5 3.076 .103 .087 3.006 .093 62.0 3.93 3.75 36134 20000
S H-334 3.346 3-11/32 85.0 3.166 .103 .090 3.092 .093 64.0 4.02 3.85 37251 21000
Sh-343 3.438 3-7/16 87.3 3.257 .103 .090 3.179 .093 66.0 4.14 3.95 38266 21900
SH-350 3.500 3-1/2 88.9 3.316 .120 .092 3.237 .109 72.0 4.16 3.98 45574 22800

RING NO. LUG HEIGHT MAXIMUM SECTION MINIMUM SECTION HOLE DIAMETER GAGING DIA. ALLOWABLE CORNER RADII & CHAMFERS MAX. LOAD м/ R max or Ch max (lbs.) EDGE MAR- GIN R.P.M. LIMITS Stan- dard Material
Gd Max.
H Tol. S max Tol. S min Tol. R Tol. R max Ch max P'r Y RPM
SH-118 .182 ±.004 .132 ±.006 .072 ±.006 .078 + .015 -.002 1.325 .064 .385 1950 .105 18000
SH-125 .183 .140 .076 .078 1.396 .068 .041 1950 .111 17000
SH-131 .183 .146 .076 .078 1.458 .068 .041 1950 .120 16500
SH-137 .184 .152 .082 .078 1.529 .072 .043 1950 .126 16000
SH-143 .184 .160 .086 .078 1.500 .076 .045 1950 .132 15000
SH-150 .214 .168 .091 .120 1.668 .079 .047 1950 .141 14800
SH-156 .235 .172 .093 .125 1.740 .082 .049 3000 .141 14000
SH-162 .235 .180 .097 .125 1.812 .087 .052 3000 .144 13200
SH-168 .235 .184 .099 .125 1.877 .090 .054 3000 .148 13000
SH-175 .237 .188 .101 .125 1.945 .091 .054 3000 .150 12200
SH-177 .237 .190 .102 .125 1.367 .092 .055 3000 .154 11700
SH-181 .262 .192 .102 .125 2.010 .092 .055 3000 .156 11500
SH-187 .262 .196 .104 .125 2.076 .094 .056 3000 .159 11000
SH-196 .262 .200 .106 .125 2.170 .094 .056 3000 .160 10500
SH-200 .262 .204 .103 .125 2.205 .096 .057 3000 .171 10000
SH-206 .267 ±.005 .208 ±.007 .111 ±.□07 .125 2.275 .098 .059 5000 .174 9600
SH-212 .280 .212 .113 .125 2.337 .098 .059 5000 .183 9500
SH-215 .280 .212 .113 .125 2.366 .097 .058 5000 .136 9400
SH-225 .280 .220 .116 .125 2.466 .100 .060 5000 .195 9200
SH-231 .280 .222 .118 .125 2.528 .100 .060 5000 .201 9000
SH-237 .292 .224 .119 .125 2.591 .100 .060 5000 .204 8800
SH-243 .260 .228 .120 .125 2.657 .102 .061 5000 .207 8600
SH-250 .292 .232 .122 .125 2.724 .104 .062 5000 .210 8400
SH-255 .268 .238 .125 .125 2.792 .108 .065 5000 .210 8200
SH-262 .292 .242 .127 .125 2.860 .1095 .066 5000 .216 8000
SH-268 .260 .246 .129 .125 2.926 .1115 .067 5000 .219 7900
SH-275 .324 .248 .131 .125 2.992 .112 .067 7350 .222 7600
SH-2B7 .324 .256 .133 .125 3.122 .115 .069 7350 .231 7300
SH-293 .324 .260 .136 .125 3.187 .116 .070 7350 .237 7200
SH-300 .264 .264 .138 .125 3.252 .117 .070 7350 .243 6700
SH-306 .293 .252 ±008 .131 ±.008 .125 3.294 .107 .064 7350 .246 6600
SH-312 .324 .272 .141 .125 3.383 .120 .072 7350 .252 6600
SH-315 .324 .274 .143 .125 3.415 .1205 .072 7350 .255 6500
SH-325 .300 .300 .145 .125 3.515 .123 .074 7350 .261 6400
SH-334 .300 .300 .147 .125 3.513 .126 .076 7350 .270 6000
SH-343 .303 .292 .148 .125 3.712 .129 .077 7350 .270 5900
SH-350 .285 .285 .148 .125 3.764 .122 .073 10500 .276 5900

RING NO. SHAFT DIAMETER GROOVE SIZE RING SIZE & WEIGHT CLEARANCE DIA. i THRUST LD. (lbs.) Sqr. Corner Abutment
DIAMETER WIDTH DEPTH FREE DIAMETER THICKNESS*** Weighl Per 1000 pcs. Ex- panded over Shaft Re- leased in Groove
Ring Safety Factor of 4 Groove Safety Factor Of 2
Ds DEC Ds FRAC Ds mm
Dq Tol. w Tol. d Df Tol. T Tol. Ib$. L1 L2 Pr Pg
SH-354 3.543 - 90.0 3.357 ±.006 .006* .120 + .005 -.000 .093 3.277 +.020 -.030 .109 ±.oo3 73.0 4.25 4.07 46183 23300
SH 362 3.825 3-5/8 92.1 3.435 .120 .095 3.352 .109 76.0 4.36 4.17 47299 24300
SH-36B 3.688 3-11/16 93.7 3.493 .120 .097 3.410 .109 80.0 4.33 4.31 48010 25300
SH-375 3.750 3-3/4 95.2 3.552 .120 .099 3.468 .109 83.0 4.52 4.33 48822 26200
SH-387 3.875 3-7/8 98.40 3.673 .120 .101 3.584 .109 88.0 4.64 4.44 50446 27700
SH-393 3.938 3-15/16 100.0 3.734 .120 .102 3.642 .109 95.0 4.70 4.50 51359 28400
SH 400 4.000 4 101.6 3.792 .120 .104 3.700 .109 101.0 4.76 4.56 52171 29400
SH-412 4.125 4-1/8 104.8 3.915 .120 .105 3.800 .109 101.2 5.00 4.78 53200 29800
5H-42S 4.250 4-1/4 108.0 4.065 .120 .092 3.989 .109 112.0 4.98 4.80 55419 27600
SH-437 4.375 4-3/8 111.1 4.190 .120 .092 4.106 .109 115.0 5.22 5.04 57043 28400
SH-450 4.500 4-1/2 114.3 4.310 .120 .095 4.223 .109 132.0 5.37 5.18 58667 30200
SH-475 4.750 4-3/4 120.6 4.550 .120 .100 4.458 .109 113.0 5.74 5.52 61015 33600
SH-500 5.000 5 127.0 4.790 .120 .105 4.692 .109 149.0 5.85 5.64 65163 37100
SH-525 5.250 5-1/4 133.3 5.030 ±.007 .006* .139 +.006 -.000 .110 4.927 +.020 -.040 .125 ±.□04 190.0 6.17 5.95 78460 40800
SH-550 5.500 5-1/2 139.7 5.265 .139 .117 5.162 .125 202.5 6.63 6.39 82215 45500
SH-575 5.750 5-3/4 146.0 5.505 .139 .122 5.396 .125 220.0 6.93 6.69 85971 49600
SH 600 6.000 6 152.4 5.745 .139 .127 5.631 .125 210.0 7.21 6.95 89625 53800
SH-625 6.250 6-1/4 158.7 5.985 ±.008 .006* .174 +.008 -.000 .132 5.866 +.020 -.050 .156 ±.005 282.0 7.48 7.22 116522 58300
SH-650 6.500 6-1/2 165.1 6.225 .174 .137 6.100 .156 ззо.о 7.80 7.45 121191 62900
SH-675 6.750 6-3/4 171.4 6.465 .174 .142 6.335 .156 356.0 8.10 7.82 125860 S7700
SH-700 7.000 7 177.8 6.705 .174 .147 6.570 +.050 -.130 .156 371.0 7.86 7.78 130529 72700
SH 725 7.250 7-1/4 184.2 6.942 .209 .154 6.775 .187 510.0 7.59 8.13 162096 78900
SH-750 7.500 7-1/2 190.5 7.180 .209 .160 7.009 .187 534.0 8.73 8.41 167678 84800
SH-775 7.750 7-3/4 196.9 7.420 .209 .165 7.243 .187 545.0 3.85 8.52 173261 90450
SH-800 8.000 8 203.2 7.660 .209 .170 7.478 .187 640.0 9.25 8.91 178843 96100
SH-B25 8.250 6-1/4 209.6 7.900 .209 .175 7.712 .187 665.0 9.54 9.19 184426 102100
SH-B50 8.500 8-1/2 215.9 8.140 .209 .180 7.947 .187 692.0 9.79 9.43 190008 108100
SH-875 8.750 6-3/4 222.3 8.380 .209 .185 8.181 .187 712.0 10.40 10.00 195591 114450
SH-900 9.000 9 228.6 8.620 .209 .190 8.415 .187 737.0 10.60 10.22 201173 120800
SH-325 9.250 9-1/4 234.9 8.860 .209 .195 8.650 .187 760.0 10.85 10.50 206756 128225
SH-950 9.500 9-1/2 241.3 9.100 .209 .200 8.885 .187 785.0 11.10 10.70 212338 134200
SH-975 9.750 9-3/4 247.6 9.338 .209 .206 9.120 .187 845.0 11.35 10.95 217921 142000
SH-1000 10.000 10 254.0 9.575 .209 .212 9.355 .187 910.0 11.60 11.20 223503 149S00

HARDNESS RANGES: STAINLESS STEEL RINGS (PH 15-7M0)

RIMG TYPE SIZE RANGE SCALE ROCKWELL HARDNESS
SH 25-81 30 N 63-69.5
87 + С 44-51

RING MO. LUG HEIGHT MAXIMUM SECTION MINIMUM SECTION HOLE DIAMETER GAGING DIA. ALLOWABLE CORNER RADII & CHAMFERS MAX. LOAD w/ R max or Ch max (lbs.) EDGE MAR GIN R.P.M. LIMITS Slan- dard Material
Gd Max.
H Tol. S max Tol. S min Tol. R Tol. R max Ch max P'r Y RPM
SH-354 .310 ±.005 .310 ±.008 .149 ±.008 .125 + .015 -.002 3.809 .123 .074 10500 .279 5800
SH ЗБ2 .3io .310 .153 .125 3.898 .127 .076 10500 .285 5700
SH-35B .310 .310 .150 .125 3.966 .130 .078 10500 .291 5600
SH-375 .342 .342 .160 .125 4.037 .133 .080 10500 .297 5500
SH-387 .342 .342 .163 .125 4.169 .137 .082 10500 .303 5100
SH-393 .342 .342 .163 .125 4.230 .137 .082 10500 .306 5200
SH 400 .342 .342 .163 .125 4.288 .135 .081 10500 .312 5000
SH-412 .380 .318 .165 .125 4.410 .135 .081 10500 .315 4900
SH-425 .342 ±.008 .342 ±.010 .176 ±.010 .125 4.558 .146 .088 10500 .276 4800
SH-437 .342 .342 .176 .125 4.683 .146 .088 10500 .276 4700
SH-450 .405 .405 .185 .125 4.860 .102 .061 10500 .285 4500
SH 475 .429 .303 .136 .125 4.096 .115 .069 10500 .300 4200
SH-500 .405 .405 .194 .156 + .020 -.005 5.346 .165 .099 10500 .315 4000
SH-525 .435 .435 .211 .156 5.605 .169 .101 13500 .330 3900
SH-550 .497 .435 .209 .156 5.867 .175 .105 13500 .351 3700
SH-575 .518 .435 .220 .156 6.134 .184 .110 13500 .366 3500
SH 600 .540 .435 .171 .156 6.302 .143 .086 13500 .381 3400
SH-BZ5 .561 ±.012 .485 ±.015 .173 ±.015 .156 6.568 .148 .089 21000 .396 3100
SH-B50 .586 .485 .236 .156 6.905 .191 .114 21000 .411 зооо
SH-575 .608 .515 .246 .187 7.172 .200 .120 21000 .426 зооо
SH-700 .530 .515 .256 .187 7.439 .208 .125 21000 .441 2900
SH 725 .660 .545 .267 .187 7.700 .214 .128 30000 .460 2800
SH-750 .676 .545 .211 .187 7.963 .220 .132 30000 .480 2700
SH-775 .660 .560 .285 .187 8.228 .227 .136 зоооо .495 2600
SH-800 .560 .560 .294 .187 8.493 .235 .141 зоооо .510 2500
SH-B25 .580 .580 .304 .187 8.758 .242 .146 зоооо .525 2400
SH 850 .580 .580 .314 .187 9.023 .250 .150 зоооо .540 2300
SH-B75 .735 .591 .322 .187 9.280 .258 .155 30000 .555 2200
SH-900 .735 .609 .333 .187 9.557 .267 .160 зоооо .570 2200
SH-B25 .735 .625 .341 .187 9.830 .274 .164 зоооо .585 2100
SH-950 .735 .642 .350 .187 10.086 .281 .168 зоооо .600 2100
SH-975 .735 .658 .358 .187 10.340 .287 .172 зоооо .618 2000
SH-1 ООО .735 .675 .367 .187 10.610 .294 .176 30000 .636 2000

HARDNESS RANGES: CARBON STEEL RINGS (SAE 1060-1090)

RING TYPE SIZE RANGE SCALE ROCKWELL HARDNESS
SH 12-23 15N 86-88
25-46 30 N 69.5-73
50-81 SON 66-71
84-102 С 47-53
106-343 С 47-52
350-700 с 44-51
725-1000 с 40-47

HARDNESS RANGES: BERYLLIUM COPPER RINGS

RING TYPE SIZE RANGE SCALE ROCKWELL HARDNESS
SH 12-23 15N 77-82"
25-102 30 N 56.5-62
106 + С 37-43

Назад в раздел

*Употребление термина "Аналог" не означает 100%-ое соответствие.

Во избежание недоразумений при приобретении изделий, уточняйте информацию у наших консультантов. Вся информация на сайте носит справочный характер и не является публичной офертой

Отзывы о
Ваше имя *
Сообщение
Отправить
Ваше сообщение успешно отправлено администраторам сайта